Printed in Formlabs grey resin at 100 microns

Printed in white and brown 1.75mm ABS filament.

Malyan M200 PETG solid black by 3DPSP scaled to 120% 0.2 mm layer height

Post processed with primer spray and acrylic paint

Colorfabb Bronzefill, sanded, weathered

0.5 scaled.

Printed on my creality CR-10 with bronzefill PLA. The print is 156 mm high and it took 34 hours to print at 0.12 mm layer height. I did not do any post-processing.

Beautiful print; came out great! Made on our Makerbot Replicator+ using MakeShaper PLA.

the thinker pla wood on DE200, buse 0.6mm

Printed by 86Duino Enjoy.

It's really nice to have high quality models from the official source.

Printed on Wanhao Duplicator i3 Mini 0.2mm layer height

Nice model, had some difficulty with the fingers but it turned out ok

Anycybic Photon 30 mm tall

Printed this out with a marble effect pla. PLA @ 200 Bed @ 45 Layer height - 0.2mm 2 walls (0.4 nozzle) Top/bottom thickness - 1.2mm Print Speed - 50 mm/s Travel Speed - 200mm/s Wall Speed - 40mm/s Infill Speed 40mm/s Infill 15% Triangle Fan Speed - 80% Retraction - 4mm @ 40mm/s Adhesion - Brim Supports - Tree

We printed this on the library's PolyPrinter 229.

PLA PIERRE GRANIT 0.6 60MM/S 30%

Ziro Marble PLA Layer : 0.2

0,12mm, with support, bronze finish

Thank you so much for this beautiful scan. I printed this 4cm tall so lots of detail got lost. Printed at 0,1 layer height, no infill with support material.

super content , je n'ai presque pas de traitement post production à faire .

Wonderful Quality of Scan

I didn't use any supports and it was a little messy under the left hand but other than that it printed really well. Awesome print!

Beautiful 3D scan, it looks wonderful. I made this one from Vertigo Starlight PLA by Fillamentum. Print time 6 hours, 100% scale, 0.2mm layer height & rectilinear supports (touching buildplate).

L'une de mes sculptures préférée signé Rodin. Imprimé avec l'anycubic photon mono x. 13h de print en 0.05 mm

Due to a print failure, had to resculpt most of the upper part of the left arm with some Milliput, but with a base coat of grey primer and some washes, none of that is very noticeable.

Printed on Labists 3D X1 / Easythreed With Labslicer (to convert in Gcode file) and change the scale. Quality mode used & 200° Celsius +/- 6 hours

Thanks a lot for "Le Penseur" ;) Magnificient :)

Sorry for the former post, I do not understand what's happened, the picture is not correct... I try new post ;) Fingers crossed

Video of make: https://youtu.be/zH94SvJDaoQ

I always wondered how sculpts would look like if painted. This started when I was told that the sculpts in the metope of Parthenon where painted and what remains today is the decoloured marble after many ages.

Some times I just try to paint, but in other cases, something provocative comes into my mind and I follow a more creative path. In any case, enjoy!

More on my creative journeys at:
Website: http://www.creativejourneys.gr

YouTube: https://www.youtube.com/channel/UCRCkvuF_oCh03GrvWeHe1HQ

Facebook: https://www.facebook.com/mycreativejourneys

I always wondered how sculpts would look like if painted. This started when I was told that the sculpts in the metope of Parthenon where painted and what remains today is the decoloured marble after many ages.

Some times I just try to paint, but in other cases, something provocative comes into my mind and I follow a more creative path. In any case, enjoy!

More on my creative journeys at:
Website: http://www.creativejourneys.gr

YouTube: https://www.youtube.com/channel/UCRCkvuF_oCh03GrvWeHe1HQ

Facebook: https://www.facebook.com/mycreativejourneys

Recomendo reduzir a velocidade de impressão na região da mão esquerda

Printer on Creality LD-006 Resin 3D printer and sprayed with gray primer.